MICROCRE · RESEARCH SCIENCE
光学玻璃与透明材料
研究目标
将折射、透过、应力和几何置于同一波长与温度条件下,区分材料表征、元件装调和系统光学性能。
研究问题
波长、厚度及收集几何是否在比较中一致?
透过损失中反射、吸收与散射各有哪些独立证据?
辅助镜、支撑和环境是否影响角度或均匀性判断?
组织与性能的关系
折射率和色散须按谱线及温度报告,不能脱离条件比较。
气泡、条纹、应力和表面状态可能作用于不同光学量,需要对应方法。
角度到高度的几何换算需要明确支点,不能替代波前或面形评价。
适用边界
棱镜耦合适用性取决于样品结构与模式,不是通用折射率方法。
材料参数合格不自动保证整机成像质量。
关联仪器、方法与研究依据
光学玻璃:均匀性、应力与光学响应 →基准平面:平面度、直线度与支撑 →自由曲面:配准、法向偏差与采样覆盖 →光学元件角度与装调尺寸链 →弯曲性能:几何、支承与脆性统计 →光学性能:透过、折射与散射边界 →
论文关联表示方法或研究对象相关,不表示论文采用了本型号仪器。
A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: I, Direct Crack Measurements →Microstructure Analysis for Additive Manufacturing: A Review of Existing Standards →Fracture Toughness Determinations by Indentation →Investigation of complementary use of optical metrology and x-ray computed tomography for surface finish in laser powder bed fusion additive manufacturing →Distance-dependent influences on angle metrology with autocollimators in deflectometry →Environmental influences on autocollimator-based angle and form metrology →Self-calibration strategies for reducing systematic slope measurement errors of autocollimators in deflectometric profilometry →A novel approach for extending autocollimator calibration from plane to spatial angles →Infrared Optical Properties of Materials →A simple method for high-precision calibration of an angle encoder using an electronic nulling autocollimator →Evaluation of measurement data — Guide to the expression of uncertainty in measurement →Evaluation of measurement data — Guide to the expression of uncertainty in measurement. Amendment 1: Nonlinearity in measurement models →Evaluation of measurement data — Supplement 1 to the GUM — Propagation of distributions using a Monte Carlo method →Guide to the expression of uncertainty in measurement — Part 6: Developing and using measurement models →Elastic/Plastic Indentation Damage in Ceramics: The Median/Radial Crack System →Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results →Traceability Calibration, & Measurement Uncertainty Issues Regarding Coordinate Measuring Machines and Other Complex Instruments →Nanoindentation of B4C-HfB2 particulate ceramic composite doped with Cr–B compounds →Comparison of Bulk and Micro Sampling Techniques for the Elemental Analysis of SRM 610 and 612 →High-Temperature Mechanical Characterization of CeO2 as a Ceramic Surrogate Fuel Based on FIB and Nanoindentation →Thermally Activated Deformation Mechanisms in MgO Investigated via High Temperature Scanning Indentation →Uncertainties in Small-Angle Measurement Systems Used to Calibrate Angle Artifacts →Certification of Standard Reference Material® 2246a Relative Intensity Correction Standard for Raman Spectroscopy: 830 nm Excitation →NIST Surface Roughness and Step Height Calibrations: Measurement Conditions and Sources of Uncertainty →Uncovering dominant mechanisms of nano-mechanical properties of AlTaO4 ceramics from structural characteristics →
