MICROCRE · RESEARCH SCIENCE
高温合金与耐热金属
研究目标
以相结构、热历史与温度化性能为主线,强调真实接触温度、氧化和时间尺度,避免把高温局部测试当作完整寿命评价。
研究问题
处理前后组织位置和局部响应能否建立一一对应?
高温位移变化中有多少来自漂移、接触热不平衡或材料变形?
局部表征与宏观蠕变之间有哪些仍未验证的尺度关系?
组织与性能的关系
析出相、晶界和方向性可共同影响响应,光学形貌不足以独立确认所有相。
温度改变材料状态和测量系统,需要把热膨胀及漂移纳入同一误差模型。
热导率组合计算要求扩散率、热容和密度处于一致温度与状态。
适用边界
炉温、样品温度和接触温度不得混用。
局部压入保荷曲线不能无验证直接给出宏观蠕变寿命。
关联仪器、方法与研究依据
论文关联表示方法或研究对象相关,不表示论文采用了本型号仪器。
Microstructure Analysis for Additive Manufacturing: A Review of Existing Standards →Limit case analysis of the “stable indenter velocity” method for obtaining creep stress exponents from constant load indentation creep tests →Investigation of creep behaviour under load during indentation experiments and its influence on hardness and modulus results →Novel high temperature vacuum nanoindentation system with active surface referencing and non-contact heating for measurements up to 800 °C →Computational modeling of the forward and reverse problems in instrumented sharp indentation →A procedure for extracting primary and secondary creep parameters from nanoindentation data →Size-affected single-slip behavior of pure nickel microcrystals →High temperature nanoindentation – the importance of isothermal contact →Development of Reference Material 8103: Adamantane for Subambient DSC Temperature and Enthalpy Calibration →Certification of Standard Reference Material® 2232a: Indium for DSC Temperature and Enthalpy Calibration →Investigation of complementary use of optical metrology and x-ray computed tomography for surface finish in laser powder bed fusion additive manufacturing →Temperature dependence of the indentation size effect →A novel approach for extending autocollimator calibration from plane to spatial angles →A critical appraisal of the extraction of creep parameters from nanoindentation data obtained at room temperature →Size dependence of mechanical properties of gold at the micron scale in the absence of strain gradients →Infrared Optical Properties of Materials →Establishing isothermal contact at a known temperature under thermal equilibrium in elevated temperature instrumented indentation testing →Evaluation of measurement data — Guide to the expression of uncertainty in measurement →Evaluation of measurement data — Guide to the expression of uncertainty in measurement. Amendment 1: Nonlinearity in measurement models →Evaluation of measurement data — Supplement 1 to the GUM — Propagation of distributions using a Monte Carlo method →Guide to the expression of uncertainty in measurement — Part 6: Developing and using measurement models →Transmission EBSD from 10 nm domains in a scanning electron microscope →Indentation power-law creep of high-purity indium →An improved long-term nanoindentation creep testing approach for studying the local deformation processes in nanocrystalline metals at room and elevated temperatures →Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results →Indentation size effects in crystalline materials: A law for strain gradient plasticity →Traceability Calibration, & Measurement Uncertainty Issues Regarding Coordinate Measuring Machines and Other Complex Instruments →Fiji: an open-source platform for biological-image analysis →NIH Image to ImageJ: 25 years of image analysis →Quantitative insight into dislocation nucleation from high-temperature nanoindentation experiments →Nanoindentation and contact-mode imaging at high temperatures →Comparison of Bulk and Micro Sampling Techniques for the Elemental Analysis of SRM 610 and 612 →Deformation mechanism and mechanical properties of TiN/ZrN nanolaminates by nanoindentation: effect of layer thickness and temperature →High-Temperature Mechanical Characterization of CeO2 as a Ceramic Surrogate Fuel Based on FIB and Nanoindentation →Thermally Activated Deformation Mechanisms in MgO Investigated via High Temperature Scanning Indentation →Hot nanoindentation in inert environments →Sample dimensions influence strength and crystal plasticity →Certification of Standard Reference Material® 2246a Relative Intensity Correction Standard for Raman Spectroscopy: 830 nm Excitation →NIST Surface Roughness and Step Height Calibrations: Measurement Conditions and Sources of Uncertainty →Elevated temperature, in situ indentation with calibrated contact temperatures →ISO Technical Committee Guidance — 热分析曲线的可比性 →Thermal Analysis →
