定义样品层级
记录各层材料、厚度、沉积/处理工艺和基体状态,确定测量正面还是截面。薄层厚度若只有估计值,应安排独立测厚,不把名义工艺参数当作实际厚度。
For films and modified layers, identify substrate contributions before choosing optical or instrumented indentation. Report roughness, contact area, depth and tip condition alongside properties.
Translation pending review.
金属膜、硬质薄层或表面改性层;多层和强各向异性材料需单独建模。
Translation pending review.
平整清洁表面、独立层厚信息、避免引入涂层损伤。
Translation pending review.
光学压痕尺寸或完整力—位移曲线、残余形貌和深厚比。
Translation pending review.
仪器化压痕:硬度、约化模量与样品模量:模型与量纲
H=Pmax/Ac;Er=√πS/(2β√Ac)
Pmax=10 mN;Ac=2 µm²;S=0.3 mN/nm;β=1.034 1;νs=0.3 1;Ei=1140 GPa;νi=0.07 1
Translation pending review.
假设弹性卸载模型适用、块体近似成立且分母为正。黏弹性、裂纹、强堆积、薄膜基体和显著各向异性可使简单求解失效。
Translation pending review.
假设输入演算:10/2 = 5 GPa;sqrt(π)×300/[2×1.034×sqrt(2)] = 181.815397 GPa;0.91/[1/181.815397−0.9951/1140] = 196.663655 GPa。约化模量与样品模量相差约14.85 GPa,原因是接触中压头也会弹性变形。数值并非只由某一个仪器显示量决定,而依赖面积、刚度、泊松比和接触模型。
Translation pending review.
基体贡献、压头钝化与面积函数
Translation pending review.
粗糙度相对压深过大
Translation pending review.
堆积、裂纹及黏弹/蠕变影响
Translation pending review.
每个载荷级的原始曲线与图像
Translation pending review.
压头校准、拟合区间和泊松比
Translation pending review.
基体影响判断及不能解释的区间
Translation pending review.
不能统一用最大深度代替接触深度。
Translation pending review.
所谓深度低于层厚某固定比例并非所有薄膜的充分条件。
记录各层材料、厚度、沉积/处理工艺和基体状态,确定测量正面还是截面。薄层厚度若只有估计值,应安排独立测厚,不把名义工艺参数当作实际厚度。
根据层厚、硬度和目标量比较维氏、努氏及仪器化压痕的适用性。小载荷并不自动保证小误差,要同时满足表面平整、端点识别或力位移分辨能力,并考虑尺寸效应。
核对力值、位移、机架柔度和压头面积函数,设置适用的参考测量。若要由卸载刚度求模量,应说明拟合区间、压头弹性参数及泊松比来源,不能把软件默认值隐去。
在不损坏目标的范围内设计多级测量,记录压痕深度与层厚的比值以及残余形貌。观察裂纹、堆积、穿透和相邻界面效应;流行的固定深厚比只是筛查经验而非所有体系的保证。
比较不同深度的结果并讨论基体、粗糙度和时间相关变形。报告为某配置下的局部或复合响应,只有模型和独立验证支持时才进一步给出薄膜本征参数及适用区间。
教学案例见本页关联计算:仪器化压痕:硬度、约化模量与样品模量。案例的载荷、尺寸和读数全部为假设,用于逐步演算及误差分析,不代表某客户、论文实测或本公司产品性能。

Explore the original technical specifications, related methods and confi

Explore the original technical specifications, related methods and confi

Explore the original technical specifications, related methods and confi

Explore the original technical specifications, related methods and confi

Explore the original technical specifications, related methods and confi

Explore the original technical specifications, related methods and confi
Links support navigation and do not establish a model’s performance or standards compliance.
Tell us about your material, specimen and measurement goal.