Methods
An autocollimator measures small tilts from image displacement after a collimated beam returns from a reflector. It supports optomechanical alignment and geometric metrology. Its direct measurand is angle; straightness and flatness also depend on the mirror base, measurement path and processing. Angular resolution alone is not system-level form accuracy.
Read more →Methods
The Brinell method presses a carbide ball into the specimen and determines hardness from the residual indentation diameter. Its larger sampling volume is useful for castings, forgings and heterogeneous metals, but does not remove the effects of segregation or porosity. Report ball diameter, test force and dwell time with every hardness result.
Read more →Methods
Grain-size measurement starts with a defined microstructural object and section. Bright and dark regions are not automatically individual grains. Intercept and planimetric methods use different counting schemes, influenced by boundary revelation, twin treatment, orientation and sampling. Consider both average scale and distribution breadth.
Read more →Methods
High-temperature indentation couples local deformation measurements to a thermal environment. Key issues include contact temperature, thermal drift, tip stability and time-dependent material deformation. Distinguish optical measurement of residual indents from instrumented force–displacement testing; their analysis methods and applicability differ.
Read more →Methods
Image analysis converts microstructural features into dimensions, area fractions or counts. Representative sampling, pixel calibration and segmentation are essential. A magnification label does not replace scale calibration, and one two-dimensional field cannot directly describe a specimen's three-dimensional structure. Define the rules before applying them to the complete image set.
Read more →Methods
Instrumented indentation records force and penetration depth continuously and estimates hardness and indentation modulus using a validated contact model. Results depend on contact detection, frame compliance, the area function, drift and unloading fits. Keep raw measurements, corrections and material interpretation distinct.
Read more →Methods
Knoop testing uses an asymmetric diamond pyramid and calculates hardness from force and the long diagonal of the residual indent. It can support narrow regions, coating cross-sections and brittle materials, but suitability still depends on dimensions, surface quality, substrate effects and optical resolution. An elongated indent does not make every thin film measurable.
Read more →Methods
Preparation should reveal the actual microstructure, not merely produce a shiny surface. Cutting heat, polishing deformation, particle pull-out and edge rounding can change the interpretation. Select a process from material hardness, phases, porosity and the observation goal, then refine it through checks between stages.
Read more →Methods
Rockwell hardness is determined from the residual increase in indentation depth under the preliminary force after a prescribed load cycle. It supports rapid comparison of many metal parts. The scale defines the indenter, forces and conversion constants; HRC, HRBW and superficial scales are different configurations. Stable support is essential.
Read more →Methods
A tensile test applies axial force under defined conditions to determine strength and ductility. Valid results depend on specimen orientation, original cross-section, gauge length, alignment and strain measurement. Crosshead motion includes grip and frame deformation and cannot replace gauge-length extension without validation.
Read more →Methods
Three-point bending loads a beam at midspan between two supports and is widely used to compare brittle materials. Maximum nominal tensile stress occurs near the midspan tensile surface. Results depend on machining, edge flaws and stressed volume. Flexural strength is neither uniaxial tensile strength nor fracture toughness.
Read more →Methods
Test plan for "Spark OES and grade identification". Specimens of tungsten carbide spray powder are measured under combustion gas corrosion following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.
Read more →Methods
Test plan for "Carbon and sulphur by combustion". Specimens of concrete core are measured under pure oxygen atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.
Read more →Methods
Test plan for "O/N/H gas analysis". Specimens of lithium battery copper foil are measured under hydrogen reducing atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "XRF non-destructive screening". Specimens of gear tooth flank are measured under nitrogen protective atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "ICP elemental analysis". Specimens of 45 carbon steel are measured under multi-gas switching O2/H2/N2/H2O following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "Chromatographic separation and purity". Specimens of 40Cr alloy structural steel are measured under space environment: vacuum, cold, radiation following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "Spectrophotometric concentration". Specimens of DC53 cold-work die steel are measured under multi-physics: thermal, mechanical, vacuum, EM following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.
Read more →Methods
Test plan for "Titration and equivalent concentration". Specimens of 2205 duplex stainless steel are measured under SHPB strain rate 1e3-1e4 /s following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Water content by Karl Fischer". Specimens of GH4169 nickel-based superalloy are measured under very-high-cycle fatigue at 20 kHz following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Melting point and crystallisation". Specimens of AlSi10Mg die-cast aluminium are measured under controlled 23±2 °C / 50±5 %RH following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Optical rotation and enantiomeric purity". Specimens of AZ91D magnesium alloy are measured under ISO Class 7 cleanroom following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Refractive index and Brix". Specimens of SiC silicon carbide ceramic are measured under in-line production environment following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "DSC and transition enthalpy". Specimens of Cf/SiC ceramic matrix composite are measured under vibration and shock environment following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "TGA and mass loss". Specimens of PEEK engineering polymer are measured under immersion in corrosive medium following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal conductivity by laser flash". Specimens of fused silica are measured under post-irradiation hot cell following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Dilatometry and CTE curve". Specimens of monocrystalline silicon wafer are measured under ambient laboratory air following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Infrared thermometry and emissivity". Specimens of electronic solder joint are measured under high vacuum 1e-4 Pa following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Gas detection and alarm thresholds". Specimens of DLC coating are measured under ultra-high vacuum 1e-7 Pa following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Petroleum distillation and flash point". Specimens of laser cladding layer are measured under vacuum thermal cycling -150 to +150 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Food composition and labelling". Specimens of wire-arc additive part are measured under thermal shock at 300 K/s following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Turbidity and suspended solids". Specimens of graphite electrode are measured under high pressure 10 MPa at 1200 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.
Read more →Methods
Test plan for "Centrifugal separation and size grading". Specimens of wood and plywood are measured under liquid nitrogen -196 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Reference materials and traceability". Specimens of battery electrode sheet are measured under liquid helium -269 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Interlaboratory comparison and proficiency". Specimens of bearing raceway are measured under high-temperature oxidation in air at 900 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "Dimensional stability under vacuum thermal cycling". Specimens of SiC silicon carbide ceramic are measured under space environment: vacuum, cold, radiation following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal cycling fatigue -150 to +150 °C". Specimens of Cf/SiC ceramic matrix composite are measured under multi-physics: thermal, mechanical, vacuum, EM following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal shock resistance at high ramp rate". Specimens of PEEK engineering polymer are measured under SHPB strain rate 1e3-1e4 /s following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.
Read more →Methods
Test plan for "Deformation under high pressure and temperature". Specimens of fused silica are measured under very-high-cycle fatigue at 20 kHz following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Mechanical properties at liquid-nitrogen temperature". Specimens of monocrystalline silicon wafer are measured under controlled 23±2 °C / 50±5 %RH following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.
Read more →Methods
Test plan for "Superconducting component testing at liquid-helium temperature". Specimens of electronic solder joint are measured under ISO Class 7 cleanroom following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Oxidation mass gain and spallation". Specimens of DLC coating are measured under in-line production environment following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Creep in steam atmosphere". Specimens of laser cladding layer are measured under vibration and shock environment following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Mechanical properties after combustion-gas corrosion". Specimens of wire-arc additive part are measured under immersion in corrosive medium following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.
Read more →Methods
Test plan for "Hydrogen embrittlement in hydrogen atmosphere". Specimens of graphite electrode are measured under post-irradiation hot cell following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.
Read more →Methods
Test plan for "Multi-gas switching cyclic test". Specimens of wood and plywood are measured under ambient laboratory air following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Combined space environment simulation". Specimens of battery electrode sheet are measured under high vacuum 1e-4 Pa following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.
Read more →Methods
Test plan for "Post-irradiation properties in vacuum at low temperature". Specimens of bearing raceway are measured under ultra-high vacuum 1e-7 Pa following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal-mechanical-electromagnetic coupling". Specimens of turbine blade film hole are measured under vacuum thermal cycling -150 to +150 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "In-situ ultra-high-temperature indentation and creep". Specimens of 20CrMnTi carburising steel are measured under thermal shock at 300 K/s following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "Hot hardness and indentation creep". Specimens of H13 hot-work tool steel are measured under high pressure 10 MPa at 1200 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal barrier coating cycle life". Specimens of 316L stainless steel weld are measured under liquid nitrogen -196 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "Oxidation of C/C composites". Specimens of TA15 titanium alloy are measured under liquid helium -269 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.
Read more →Methods
Test plan for "Strength retention of Cf/SiC at high temperature". Specimens of Ti-6Al-4V additively manufactured part are measured under high-temperature oxidation in air at 900 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Outgassing and contamination control". Specimens of 2024 aluminium riveted joint are measured under steam atmosphere at 800 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Grip drift correction under thermal cycling". Specimens of Si3N4 silicon nitride ceramic are measured under combustion gas corrosion following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Effect of thermal gradient on measurement". Specimens of C/C composite are measured under pure oxygen atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Safety interlock for extreme-environment testing". Specimens of glass-fibre reinforced nylon are measured under hydrogen reducing atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Chamber calibration and uniformity verification". Specimens of silicone rubber O-ring are measured under nitrogen protective atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Rockwell hardness and hardened case evaluation". Specimens of 45 carbon steel are measured under ambient laboratory air following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Brinell hardness on coarse cast structures". Specimens of 40Cr alloy structural steel are measured under high vacuum 1e-4 Pa following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Vickers hardness profile and case depth". Specimens of DC53 cold-work die steel are measured under ultra-high vacuum 1e-7 Pa following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Microhardness matched to coating thickness". Specimens of 2205 duplex stainless steel are measured under vacuum thermal cycling -150 to +150 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Knoop hardness on brittle ceramics". Specimens of GH4169 nickel-based superalloy are measured under thermal shock at 300 K/s following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Leeb hardness in the field and conversion checks". Specimens of AlSi10Mg die-cast aluminium are measured under high pressure 10 MPa at 1200 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Shore and Barcol hardness on elastomers". Specimens of AZ91D magnesium alloy are measured under liquid nitrogen -196 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Limits of Rockwell to Brinell conversion". Specimens of SiC silicon carbide ceramic are measured under liquid helium -269 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Indentation size effect and load selection". Specimens of Cf/SiC ceramic matrix composite are measured under high-temperature oxidation in air at 900 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Hardness mapping across a weld heat-affected zone". Specimens of PEEK engineering polymer are measured under steam atmosphere at 800 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Effective case depth of carburised layers". Specimens of fused silica are measured under combustion gas corrosion following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.
Read more →Methods
Test plan for "Induction-hardened depth and transition zone". Specimens of monocrystalline silicon wafer are measured under pure oxygen atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Nitrided layer hardness and brittleness rating". Specimens of electronic solder joint are measured under hydrogen reducing atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Laser-hardened track overlap evaluation". Specimens of DLC coating are measured under nitrogen protective atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "Hardness anisotropy in additively manufactured parts". Specimens of laser cladding layer are measured under multi-gas switching O2/H2/N2/H2O following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.
Read more →Methods
Test plan for "Hot hardness and softening onset". Specimens of wire-arc additive part are measured under space environment: vacuum, cold, radiation following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.
Read more →Methods
Test plan for "Low-temperature hardness and ductile-brittle transition". Specimens of graphite electrode are measured under multi-physics: thermal, mechanical, vacuum, EM following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.
Read more →Methods
Test plan for "In-situ vacuum high-temperature indentation". Specimens of wood and plywood are measured under SHPB strain rate 1e3-1e4 /s following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Separating coating hardness from substrate effect". Specimens of battery electrode sheet are measured under very-high-cycle fatigue at 20 kHz following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.
Read more →Methods
Test plan for "Daily verification with reference blocks". Specimens of bearing raceway are measured under controlled 23±2 °C / 50±5 %RH following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.
Read more →Methods
Test plan for "Indenter geometry and area-function calibration". Specimens of turbine blade film hole are measured under ISO Class 7 cleanroom following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.
Read more →Methods
Test plan for "Uncertainty budget for hardness measurement". Specimens of 20CrMnTi carburising steel are measured under in-line production environment following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Empirical hardness to tensile strength correlation". Specimens of H13 hot-work tool steel are measured under vibration and shock environment following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.
Read more →Methods
Test plan for "Hardness sampling on small and thin parts". Specimens of 316L stainless steel weld are measured under immersion in corrosive medium following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Room-temperature tensile and yield strength". Specimens of Ti-6Al-4V additively manufactured part are measured under combustion gas corrosion following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Elevated-temperature tensile testing". Specimens of 2024 aluminium riveted joint are measured under pure oxygen atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.
Read more →Methods
Test plan for "Cryogenic tensile and transition behaviour". Specimens of Si3N4 silicon nitride ceramic are measured under hydrogen reducing atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.
Read more →Methods
Test plan for "Compression behaviour and buckling check". Specimens of C/C composite are measured under nitrogen protective atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Three- and four-point bending". Specimens of glass-fibre reinforced nylon are measured under multi-gas switching O2/H2/N2/H2O following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.
Read more →Methods
Test plan for "Shear strength of riveted joints". Specimens of silicone rubber O-ring are measured under space environment: vacuum, cold, radiation following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.
Read more →Methods
Test plan for "Torsion and shear modulus". Specimens of sapphire window are measured under multi-physics: thermal, mechanical, vacuum, EM following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Charpy impact and absorbed energy". Specimens of copper lead frame are measured under SHPB strain rate 1e3-1e4 /s following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "Low-temperature impact and fracture appearance". Specimens of TiN coating are measured under very-high-cycle fatigue at 20 kHz following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "SHPB dynamic compression at high strain rate". Specimens of electroplated nickel layer are measured under controlled 23±2 °C / 50±5 %RH following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "High-cycle fatigue S-N curve". Specimens of laser weld are measured under ISO Class 7 cleanroom following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.
Read more →Methods
Test plan for "Ultrasonic very-high-cycle fatigue". Specimens of powder metallurgy sintered part are measured under in-line production environment following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Crack growth rate da/dN". Specimens of basalt fibre panel are measured under vibration and shock environment following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Fracture toughness K_IC and J-integral". Specimens of rock thin section are measured under immersion in corrosive medium following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Creep and stress rupture". Specimens of photovoltaic ribbon are measured under post-irradiation hot cell following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Stress relaxation and preload loss". Specimens of guideway surface are measured under ambient laboratory air following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Residual stress by hole drilling and indentation". Specimens of 42CrMo quenched and tempered steel are measured under high vacuum 1e-4 Pa following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Interlaminar shear of composites". Specimens of GCr15 bearing steel are measured under ultra-high vacuum 1e-7 Pa following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Bonded peel and lap-shear strength". Specimens of 304 austenitic stainless steel are measured under vacuum thermal cycling -150 to +150 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Torque–preload relationship of fasteners". Specimens of TC4 titanium alloy are measured under thermal shock at 300 K/s following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Multiaxial fatigue with phase-shifted loading". Specimens of Inconel 718 additively manufactured part are measured under high pressure 10 MPa at 1200 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermomechanical fatigue life". Specimens of 7075 aluminium alloy are measured under liquid nitrogen -196 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Strain-rate sensitivity". Specimens of ZTA zirconia-toughened alumina are measured under liquid helium -269 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Grip compliance and frame correction". Specimens of Al2O3 alumina ceramic are measured under high-temperature oxidation in air at 900 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Vision measurement of 2D profiles". Specimens of laser cladding layer are measured under high pressure 10 MPa at 1200 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "CMM measurement and position tolerance". Specimens of wire-arc additive part are measured under liquid nitrogen -196 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Roundness and cylindricity evaluation". Specimens of graphite electrode are measured under liquid helium -269 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Profile tolerance of free-form surfaces". Specimens of wood and plywood are measured under high-temperature oxidation in air at 900 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Roughness Ra/Rz and filtering". Specimens of battery electrode sheet are measured under steam atmosphere at 800 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Height and step measurement". Specimens of bearing raceway are measured under combustion gas corrosion following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Coating and sheet thickness". Specimens of turbine blade film hole are measured under pure oxygen atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Ultrasonic testing and indication sizing". Specimens of 20CrMnTi carburising steel are measured under hydrogen reducing atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Magnetic particle and penetrant testing". Specimens of H13 hot-work tool steel are measured under nitrogen protective atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Eddy current testing and conductivity". Specimens of 316L stainless steel weld are measured under multi-gas switching O2/H2/N2/H2O following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Vibration spectrum and fault diagnosis". Specimens of TA15 titanium alloy are measured under space environment: vacuum, cold, radiation following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Borescope inspection of internal features". Specimens of Ti-6Al-4V additively manufactured part are measured under multi-physics: thermal, mechanical, vacuum, EM following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Thread and gear parameter measurement". Specimens of 2024 aluminium riveted joint are measured under SHPB strain rate 1e3-1e4 /s following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Large-part measurement in situ". Specimens of Si3N4 silicon nitride ceramic are measured under very-high-cycle fatigue at 20 kHz following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.
Read more →Methods
Test plan for "Temperature compensation and CTE correction". Specimens of C/C composite are measured under controlled 23±2 °C / 50±5 %RH following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Point strategy and uncertainty". Specimens of glass-fibre reinforced nylon are measured under ISO Class 7 cleanroom following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Probe performance verification". Specimens of silicone rubber O-ring are measured under in-line production environment following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "In-line inspection and cycle time". Specimens of sapphire window are measured under vibration and shock environment following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.
Read more →Methods
Test plan for "Automated loading integrated with measurement". Specimens of copper lead frame are measured under immersion in corrosive medium following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.
Read more →Methods
Test plan for "Vision guidance and robot positioning". Specimens of TiN coating are measured under post-irradiation hot cell following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.
Read more →Methods
Test plan for "Positioning accuracy of a precision stage". Specimens of electroplated nickel layer are measured under ambient laboratory air following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Writing an NDT procedure". Specimens of laser weld are measured under high vacuum 1e-4 Pa following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.
Read more →Methods
Test plan for "Acceptance levels for indications". Specimens of powder metallurgy sintered part are measured under ultra-high vacuum 1e-7 Pa following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.
Read more →Methods
Test plan for "Measurement system analysis". Specimens of basalt fibre panel are measured under vacuum thermal cycling -150 to +150 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.
Read more →Methods
Test plan for "Grain size rating and statistics". Specimens of copper lead frame are measured under ambient laboratory air following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Phase fraction by area analysis". Specimens of TiN coating are measured under high vacuum 1e-4 Pa following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Inclusion rating". Specimens of electroplated nickel layer are measured under ultra-high vacuum 1e-7 Pa following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Graphite morphology and nodularity". Specimens of laser weld are measured under vacuum thermal cycling -150 to +150 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Coating thickness and interface morphology". Specimens of powder metallurgy sintered part are measured under thermal shock at 300 K/s following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Weld penetration and heat-affected zone". Specimens of basalt fibre panel are measured under high pressure 10 MPa at 1200 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Melt pool and porosity in additive parts". Specimens of rock thin section are measured under liquid nitrogen -196 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.
Read more →Methods
Test plan for "Cleanliness particle counting and classification". Specimens of photovoltaic ribbon are measured under liquid helium -269 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Bubble size distribution". Specimens of guideway surface are measured under high-temperature oxidation in air at 900 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Fibre orientation and distribution". Specimens of 42CrMo quenched and tempered steel are measured under steam atmosphere at 800 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "Crack length and propagation path". Specimens of GCr15 bearing steel are measured under combustion gas corrosion following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.
Read more →Methods
Test plan for "Fractography and failure mode". Specimens of 304 austenitic stainless steel are measured under pure oxygen atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.
Read more →Methods
Test plan for "Corrosion pit depth and density". Specimens of TC4 titanium alloy are measured under hydrogen reducing atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.
Read more →Methods
Test plan for "Surface defect and scratch measurement". Specimens of Inconel 718 additively manufactured part are measured under nitrogen protective atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Anisotropic structure under polarised light". Specimens of 7075 aluminium alloy are measured under multi-gas switching O2/H2/N2/H2O following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.
Read more →Methods
Test plan for "Fluorescence labelling and biological samples". Specimens of ZTA zirconia-toughened alumina are measured under space environment: vacuum, cold, radiation following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.
Read more →Methods
Test plan for "Stereo observation and 3D topography". Specimens of Al2O3 alumina ceramic are measured under multi-physics: thermal, mechanical, vacuum, EM following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.
Read more →Methods
Test plan for "Automated stitching of large fields". Specimens of carbon-fibre epoxy laminate are measured under SHPB strain rate 1e3-1e4 /s following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Dimensional measurement and calibration". Specimens of PTFE seal are measured under very-high-cycle fatigue at 20 kHz following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.
Read more →Methods
Test plan for "AI-assisted phase recognition and segmentation". Specimens of BK7 optical glass are measured under controlled 23±2 °C / 50±5 %RH following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Correlating micrographs with hardness indents". Specimens of SiC power device solder layer are measured under ISO Class 7 cleanroom following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Choosing illumination and contrast mode". Specimens of WC-Co cemented carbide are measured under in-line production environment following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Image drift and focus stability". Specimens of thermal barrier coating are measured under vibration and shock environment following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.
Read more →Methods
Test plan for "Reproducibility of image measurements". Specimens of friction stir weld are measured under immersion in corrosive medium following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.
Read more →Methods
Test plan for "Guideway straightness with pitch and yaw". Specimens of PTFE seal are measured under ISO Class 7 cleanroom following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Angular error of a machine table". Specimens of BK7 optical glass are measured under in-line production environment following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Rotary table indexing error and backlash". Specimens of SiC power device solder layer are measured under vibration and shock environment following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "Parallelism of a straightedge and datum". Specimens of WC-Co cemented carbide are measured under immersion in corrosive medium following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.
Read more →Methods
Test plan for "Segmented stitching over long travel". Specimens of thermal barrier coating are measured under post-irradiation hot cell following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.
Read more →Methods
Test plan for "Flatness of an optical table". Specimens of friction stir weld are measured under ambient laboratory air following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.
Read more →Methods
Test plan for "Prism angle and refractive index". Specimens of cold-sprayed coating are measured under high vacuum 1e-4 Pa following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Substrate figure and wedge angle". Specimens of tungsten carbide spray powder are measured under ultra-high vacuum 1e-7 Pa following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.
Read more →Methods
Test plan for "Boresight parallelism of a telescope". Specimens of concrete core are measured under vacuum thermal cycling -150 to +150 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.
Read more →Methods
Test plan for "Polygon and autocollimator combination". Specimens of lithium battery copper foil are measured under thermal shock at 300 K/s following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.
Read more →Methods
Test plan for "Abbe and cosine error correction". Specimens of gear tooth flank are measured under high pressure 10 MPa at 1200 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal drift in angular readings". Specimens of 45 carbon steel are measured under liquid nitrogen -196 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.
Read more →Methods
Test plan for "Air turbulence and refractive index gradient". Specimens of 40Cr alloy structural steel are measured under liquid helium -269 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Collimation and focus judgement at long focal length". Specimens of DC53 cold-work die steel are measured under high-temperature oxidation in air at 900 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Cross-check with laser interferometry". Specimens of 2205 duplex stainless steel are measured under steam atmosphere at 800 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Sampling and filtering in photoelectric autocollimation". Specimens of GH4169 nickel-based superalloy are measured under combustion gas corrosion following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.
Read more →Methods
Test plan for "Verifying sub-microradian resolution". Specimens of AlSi10Mg die-cast aluminium are measured under pure oxygen atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.
Read more →Methods
Test plan for "Straightness calibration of a precision stage". Specimens of AZ91D magnesium alloy are measured under hydrogen reducing atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Closed-loop feedback for precision motion". Specimens of SiC silicon carbide ceramic are measured under nitrogen protective atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.
Read more →Methods
Test plan for "Thermal stability of granite and ceramic datums". Specimens of Cf/SiC ceramic matrix composite are measured under multi-gas switching O2/H2/N2/H2O following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.
Read more →Methods
Test plan for "Autocollimation in vacuum or at low temperature". Specimens of PEEK engineering polymer are measured under space environment: vacuum, cold, radiation following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Coaxiality of an optical assembly". Specimens of fused silica are measured under multi-physics: thermal, mechanical, vacuum, EM following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "Uncertainty and traceability chain". Specimens of monocrystalline silicon wafer are measured under SHPB strain rate 1e3-1e4 /s following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "Field versus laboratory agreement". Specimens of electronic solder joint are measured under very-high-cycle fatigue at 20 kHz following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "Cutting burn control on hardened steel". Specimens of 304 austenitic stainless steel are measured under high pressure 10 MPa at 1200 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "Distortion-free sectioning of sheet and foil". Specimens of TC4 titanium alloy are measured under liquid nitrogen -196 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "Retaining coating edges in cross-section". Specimens of Inconel 718 additively manufactured part are measured under liquid helium -269 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "Mounting and chamfering of thermal-spray coatings". Specimens of 7075 aluminium alloy are measured under high-temperature oxidation in air at 900 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.
Read more →Methods
Test plan for "Vacuum impregnation of porous materials". Specimens of ZTA zirconia-toughened alumina are measured under steam atmosphere at 800 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Avoiding smearing between composite plies". Specimens of Al2O3 alumina ceramic are measured under combustion gas corrosion following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Preventing scratches and embedded abrasive in soft metals". Specimens of carbon-fibre epoxy laminate are measured under pure oxygen atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Diamond polishing of ceramics and cemented carbide". Specimens of PTFE seal are measured under hydrogen reducing atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Electrolytic polishing of aluminium alloys". Specimens of BK7 optical glass are measured under nitrogen protective atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Avoiding hydrogen pickup in titanium preparation". Specimens of SiC power device solder layer are measured under multi-gas switching O2/H2/N2/H2O following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Sectioning across weld zones". Specimens of WC-Co cemented carbide are measured under space environment: vacuum, cold, radiation following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Measuring heat-affected zone width". Specimens of thermal barrier coating are measured under multi-physics: thermal, mechanical, vacuum, EM following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Preparation for grain size measurement". Specimens of friction stir weld are measured under SHPB strain rate 1e3-1e4 /s following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Consistency for inclusion rating". Specimens of cold-sprayed coating are measured under very-high-cycle fatigue at 20 kHz following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
Test plan for "Preserving graphite morphology in cast iron". Specimens of tungsten carbide spray powder are measured under controlled 23±2 °C / 50±5 %RH following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.
Read more →Methods
Test plan for "Porosity preparation for additive parts". Specimens of concrete core are measured under ISO Class 7 cleanroom following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.
Read more →Methods
Test plan for "Cross-sectioning of battery electrodes". Specimens of lithium battery copper foil are measured under in-line production environment following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.
Read more →Methods
Test plan for "Ion-beam polishing of semiconductor cross-sections". Specimens of gear tooth flank are measured under vibration and shock environment following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.
Read more →Methods
Test plan for "Petrographic thin section preparation". Specimens of 45 carbon steel are measured under immersion in corrosive medium following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.
Read more →Methods
Test plan for "Protecting fracture surfaces during sectioning". Specimens of 40Cr alloy structural steel are measured under post-irradiation hot cell following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.
Read more →Methods
Test plan for "Reproducible automatic polishing parameters". Specimens of DC53 cold-work die steel are measured under ambient laboratory air following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.
Read more →Methods
Test plan for "Effect of preparation quality on hardness". Specimens of 2205 duplex stainless steel are measured under high vacuum 1e-4 Pa following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.
Read more →Methods
Test plan for "Consumable selection and cost control". Specimens of GH4169 nickel-based superalloy are measured under ultra-high vacuum 1e-7 Pa following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.
Read more →Methods
Test plan for "Preparation safety and waste handling". Specimens of AlSi10Mg die-cast aluminium are measured under vacuum thermal cycling -150 to +150 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.
Read more →Methods
Test plan for "3D-printed specimens and conformal fixtures". Specimens of photovoltaic ribbon are measured under space environment: vacuum, cold, radiation following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.
Read more →Methods
Test plan for "Teaching practice and operator assessment". Specimens of guideway surface are measured under multi-physics: thermal, mechanical, vacuum, EM following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Hardness consumables and indenter management". Specimens of 42CrMo quenched and tempered steel are measured under SHPB strain rate 1e3-1e4 /s following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Consumable consistency across batches". Specimens of GCr15 bearing steel are measured under very-high-cycle fatigue at 20 kHz following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.
Read more →Methods
Test plan for "Automated sample pre-treatment". Specimens of 304 austenitic stainless steel are measured under controlled 23±2 °C / 50±5 %RH following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.
Read more →Methods
Test plan for "Automated handling with barcode traceability". Specimens of TC4 titanium alloy are measured under ISO Class 7 cleanroom following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.
Read more →Methods
Test plan for "Robot and vision positioning". Specimens of Inconel 718 additively manufactured part are measured under in-line production environment following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.
Read more →Methods
Test plan for "Instrument interface and LIMS". Specimens of 7075 aluminium alloy are measured under vibration and shock environment following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.
Read more →Methods
Test plan for "Raising acquisition from 40 Hz to 100 Hz". Specimens of ZTA zirconia-toughened alumina are measured under immersion in corrosive medium following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.
Read more →Methods
Test plan for "Synchronised force and displacement at high temperature". Specimens of Al2O3 alumina ceramic are measured under post-irradiation hot cell following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Servo bandwidth and motion smoothness". Specimens of carbon-fibre epoxy laminate are measured under ambient laboratory air following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.
Read more →Methods
Test plan for "Full automation and unattended operation". Specimens of PTFE seal are measured under high vacuum 1e-4 Pa following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.
Read more →Methods
Test plan for "Retrofit of legacy instruments". Specimens of BK7 optical glass are measured under ultra-high vacuum 1e-7 Pa following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.
Read more →Methods
Test plan for "AI material database and selection advice". Specimens of SiC power device solder layer are measured under vacuum thermal cycling -150 to +150 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.
Read more →Methods
Test plan for "AI property prediction from experiments". Specimens of WC-Co cemented carbide are measured under thermal shock at 300 K/s following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.
Read more →Methods
Test plan for "Automated test-sequence orchestration". Specimens of thermal barrier coating are measured under high pressure 10 MPa at 1200 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Condition monitoring and predictive maintenance". Specimens of friction stir weld are measured under liquid nitrogen -196 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.
Read more →Methods
Test plan for "Calibration interval and intermediate checks". Specimens of cold-sprayed coating are measured under liquid helium -269 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.
Read more →Methods
Test plan for "Laboratory safety and emergency stop". Specimens of tungsten carbide spray powder are measured under high-temperature oxidation in air at 900 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.
Read more →Methods
Test plan for "Central monitoring of multiple instruments". Specimens of concrete core are measured under steam atmosphere at 800 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.
Read more →Methods
Test plan for "Data integrity and audit trail". Specimens of lithium battery copper foil are measured under combustion gas corrosion following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.
Read more →Methods
Test plan for "Method files and work instructions". Specimens of gear tooth flank are measured under pure oxygen atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.
Read more →Methods
Test plan for "Training and competence matrix". Specimens of 45 carbon steel are measured under hydrogen reducing atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.
Read more →Methods
Test plan for "Acceptance and rollback of a retrofit". Specimens of 40Cr alloy structural steel are measured under nitrogen protective atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.
Read more →Methods
A diamond pyramid produces an indent under a specified force. The two diagonals measured after unloading give local hardness. The method supports comparisons of metallic microstructures, heat-treated layers and weld regions. Thin layers, rough surfaces and very small indents require a suitability assessment; the ability to apply a load does not establish measurement validity.
Read more →