SHANGHAI MICROCRE OPTICS-MECH TECH CO., LTDAbout MICROCRE400-812-7833
MICROCRE · KNOWLEDGE & INSTRUMENTS

Applications

Reviewed information connects instruments, methods and materials research.

228 records · All content ↗

Applications

Advanced ceramics and brittle composites

Build screening around densification, pores, local hardness and cracking. Because preparation can cause chipping and pull-out, first validate the surface, then combine quantitative microscopy with loading studies. Sectional defects, indentation cracks and standard fracture toughness are different results.

Read more →
Applications

Aerospace and high-temperature structural materials

For superalloys, lightweight alloys and coatings, connect processing state, thermal exposure and sampling location. Combine microstructure, local hardness and mechanical tests as complementary evidence, while distinguishing laboratory characterisation from component qualification and actual service conditions.

Read more →
Applications

Automotive manufacturing and critical components

Link incoming material, heat treatment, joining and failure investigation. Select hardness profiles, microscopy and mechanical tests for gears, fasteners, castings and welds, keeping comparable batch records. This workflow does not replace component acceptance specifications or release decisions.

Read more →
Applications

Energy equipment, welds and service-exposed materials

Assess pipes, welded joints and heat-exposed materials through microstructure, hardness and mechanical evidence. Record service history, corrosion and location before interpretation. Laboratory screening supports investigation, while remaining-life or continued-service decisions require dedicated engineering assessment.

Read more →
Applications

Universities, research institutes and shared laboratories

Configure instruments around the scientific question. Translate material, scale, environment and measurand into testable conditions, then organise preparation, measurement, analysis and replication. Shared laboratories also need training, method versions and raw-data retention for meaningful cross-user comparisons.

Read more →
Applications

Semiconductors, packaging and microelectronics

Create a path from locating small targets to section analysis. For package interfaces, joints, layers and local defects, control material removal, edge retention and imaging capability. Optical microscopy provides sectional morphology and dimensions; finer structures need other suitable techniques.

Read more →
Applications

Spark OES and grade identification: industry application

Test plan for "Spark OES and grade identification". Specimens of tungsten carbide spray powder are measured under combustion gas corrosion following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.

Read more →
Applications

Carbon and sulphur by combustion: industry application

Test plan for "Carbon and sulphur by combustion". Specimens of concrete core are measured under pure oxygen atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.

Read more →
Applications

O/N/H gas analysis: industry application

Test plan for "O/N/H gas analysis". Specimens of lithium battery copper foil are measured under hydrogen reducing atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.

Read more →
Applications

XRF non-destructive screening: industry application

Test plan for "XRF non-destructive screening". Specimens of gear tooth flank are measured under nitrogen protective atmosphere following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

ICP elemental analysis: industry application

Test plan for "ICP elemental analysis". Specimens of 45 carbon steel are measured under multi-gas switching O2/H2/N2/H2O following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

Chromatographic separation and purity: industry application

Test plan for "Chromatographic separation and purity". Specimens of 40Cr alloy structural steel are measured under space environment: vacuum, cold, radiation following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

Spectrophotometric concentration: industry application

Test plan for "Spectrophotometric concentration". Specimens of DC53 cold-work die steel are measured under multi-physics: thermal, mechanical, vacuum, EM following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.

Read more →
Applications

Titration and equivalent concentration: industry application

Test plan for "Titration and equivalent concentration". Specimens of 2205 duplex stainless steel are measured under SHPB strain rate 1e3-1e4 /s following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

Water content by Karl Fischer: industry application

Test plan for "Water content by Karl Fischer". Specimens of GH4169 nickel-based superalloy are measured under very-high-cycle fatigue at 20 kHz following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Melting point and crystallisation: industry application

Test plan for "Melting point and crystallisation". Specimens of AlSi10Mg die-cast aluminium are measured under controlled 23±2 °C / 50±5 %RH following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Optical rotation and enantiomeric purity: industry application

Test plan for "Optical rotation and enantiomeric purity". Specimens of AZ91D magnesium alloy are measured under ISO Class 7 cleanroom following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Refractive index and Brix: industry application

Test plan for "Refractive index and Brix". Specimens of SiC silicon carbide ceramic are measured under in-line production environment following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

DSC and transition enthalpy: industry application

Test plan for "DSC and transition enthalpy". Specimens of Cf/SiC ceramic matrix composite are measured under vibration and shock environment following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

TGA and mass loss: industry application

Test plan for "TGA and mass loss". Specimens of PEEK engineering polymer are measured under immersion in corrosive medium following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Thermal conductivity by laser flash: industry application

Test plan for "Thermal conductivity by laser flash". Specimens of fused silica are measured under post-irradiation hot cell following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Dilatometry and CTE curve: industry application

Test plan for "Dilatometry and CTE curve". Specimens of monocrystalline silicon wafer are measured under ambient laboratory air following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Infrared thermometry and emissivity: industry application

Test plan for "Infrared thermometry and emissivity". Specimens of electronic solder joint are measured under high vacuum 1e-4 Pa following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Gas detection and alarm thresholds: industry application

Test plan for "Gas detection and alarm thresholds". Specimens of DLC coating are measured under ultra-high vacuum 1e-7 Pa following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Petroleum distillation and flash point: industry application

Test plan for "Petroleum distillation and flash point". Specimens of laser cladding layer are measured under vacuum thermal cycling -150 to +150 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Food composition and labelling: industry application

Test plan for "Food composition and labelling". Specimens of wire-arc additive part are measured under thermal shock at 300 K/s following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Turbidity and suspended solids: industry application

Test plan for "Turbidity and suspended solids". Specimens of graphite electrode are measured under high pressure 10 MPa at 1200 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.

Read more →
Applications

Centrifugal separation and size grading: industry application

Test plan for "Centrifugal separation and size grading". Specimens of wood and plywood are measured under liquid nitrogen -196 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Reference materials and traceability: industry application

Test plan for "Reference materials and traceability". Specimens of battery electrode sheet are measured under liquid helium -269 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Interlaboratory comparison and proficiency: industry application

Test plan for "Interlaboratory comparison and proficiency". Specimens of bearing raceway are measured under high-temperature oxidation in air at 900 °C following compositional and thermal analysis. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

Dimensional stability under vacuum thermal cycling: industry application

Test plan for "Dimensional stability under vacuum thermal cycling". Specimens of SiC silicon carbide ceramic are measured under space environment: vacuum, cold, radiation following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.

Read more →
Applications

Thermal cycling fatigue -150 to +150 °C: industry application

Test plan for "Thermal cycling fatigue -150 to +150 °C". Specimens of Cf/SiC ceramic matrix composite are measured under multi-physics: thermal, mechanical, vacuum, EM following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.

Read more →
Applications

Thermal shock resistance at high ramp rate: industry application

Test plan for "Thermal shock resistance at high ramp rate". Specimens of PEEK engineering polymer are measured under SHPB strain rate 1e3-1e4 /s following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.

Read more →
Applications

Deformation under high pressure and temperature: industry application

Test plan for "Deformation under high pressure and temperature". Specimens of fused silica are measured under very-high-cycle fatigue at 20 kHz following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.

Read more →
Applications

Mechanical properties at liquid-nitrogen temperature: industry application

Test plan for "Mechanical properties at liquid-nitrogen temperature". Specimens of monocrystalline silicon wafer are measured under controlled 23±2 °C / 50±5 %RH following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.

Read more →
Applications

Oxidation mass gain and spallation: industry application

Test plan for "Oxidation mass gain and spallation". Specimens of DLC coating are measured under in-line production environment following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.

Read more →
Applications

Creep in steam atmosphere: industry application

Test plan for "Creep in steam atmosphere". Specimens of laser cladding layer are measured under vibration and shock environment following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.

Read more →
Applications

Mechanical properties after combustion-gas corrosion: industry application

Test plan for "Mechanical properties after combustion-gas corrosion". Specimens of wire-arc additive part are measured under immersion in corrosive medium following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.

Read more →
Applications

Hydrogen embrittlement in hydrogen atmosphere: industry application

Test plan for "Hydrogen embrittlement in hydrogen atmosphere". Specimens of graphite electrode are measured under post-irradiation hot cell following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.

Read more →
Applications

Multi-gas switching cyclic test: industry application

Test plan for "Multi-gas switching cyclic test". Specimens of wood and plywood are measured under ambient laboratory air following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.

Read more →
Applications

Combined space environment simulation: industry application

Test plan for "Combined space environment simulation". Specimens of battery electrode sheet are measured under high vacuum 1e-4 Pa following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.

Read more →
Applications

Post-irradiation properties in vacuum at low temperature: industry application

Test plan for "Post-irradiation properties in vacuum at low temperature". Specimens of bearing raceway are measured under ultra-high vacuum 1e-7 Pa following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.

Read more →
Applications

Thermal-mechanical-electromagnetic coupling: industry application

Test plan for "Thermal-mechanical-electromagnetic coupling". Specimens of turbine blade film hole are measured under vacuum thermal cycling -150 to +150 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.

Read more →
Applications

In-situ ultra-high-temperature indentation and creep: industry application

Test plan for "In-situ ultra-high-temperature indentation and creep". Specimens of 20CrMnTi carburising steel are measured under thermal shock at 300 K/s following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

Hot hardness and indentation creep: industry application

Test plan for "Hot hardness and indentation creep". Specimens of H13 hot-work tool steel are measured under high pressure 10 MPa at 1200 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

Thermal barrier coating cycle life: industry application

Test plan for "Thermal barrier coating cycle life". Specimens of 316L stainless steel weld are measured under liquid nitrogen -196 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

Oxidation of C/C composites: industry application

Test plan for "Oxidation of C/C composites". Specimens of TA15 titanium alloy are measured under liquid helium -269 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.

Read more →
Applications

Strength retention of Cf/SiC at high temperature: industry application

Test plan for "Strength retention of Cf/SiC at high temperature". Specimens of Ti-6Al-4V additively manufactured part are measured under high-temperature oxidation in air at 900 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

Outgassing and contamination control: industry application

Test plan for "Outgassing and contamination control". Specimens of 2024 aluminium riveted joint are measured under steam atmosphere at 800 °C following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Grip drift correction under thermal cycling: industry application

Test plan for "Grip drift correction under thermal cycling". Specimens of Si3N4 silicon nitride ceramic are measured under combustion gas corrosion following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Effect of thermal gradient on measurement: industry application

Test plan for "Effect of thermal gradient on measurement". Specimens of C/C composite are measured under pure oxygen atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Safety interlock for extreme-environment testing: industry application

Test plan for "Safety interlock for extreme-environment testing". Specimens of glass-fibre reinforced nylon are measured under hydrogen reducing atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Chamber calibration and uniformity verification: industry application

Test plan for "Chamber calibration and uniformity verification". Specimens of silicone rubber O-ring are measured under nitrogen protective atmosphere following extreme-environment testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Rockwell hardness and hardened case evaluation: industry application

Test plan for "Rockwell hardness and hardened case evaluation". Specimens of 45 carbon steel are measured under ambient laboratory air following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Brinell hardness on coarse cast structures: industry application

Test plan for "Brinell hardness on coarse cast structures". Specimens of 40Cr alloy structural steel are measured under high vacuum 1e-4 Pa following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Vickers hardness profile and case depth: industry application

Test plan for "Vickers hardness profile and case depth". Specimens of DC53 cold-work die steel are measured under ultra-high vacuum 1e-7 Pa following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Microhardness matched to coating thickness: industry application

Test plan for "Microhardness matched to coating thickness". Specimens of 2205 duplex stainless steel are measured under vacuum thermal cycling -150 to +150 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Knoop hardness on brittle ceramics: industry application

Test plan for "Knoop hardness on brittle ceramics". Specimens of GH4169 nickel-based superalloy are measured under thermal shock at 300 K/s following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Leeb hardness in the field and conversion checks: industry application

Test plan for "Leeb hardness in the field and conversion checks". Specimens of AlSi10Mg die-cast aluminium are measured under high pressure 10 MPa at 1200 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Shore and Barcol hardness on elastomers: industry application

Test plan for "Shore and Barcol hardness on elastomers". Specimens of AZ91D magnesium alloy are measured under liquid nitrogen -196 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Limits of Rockwell to Brinell conversion: industry application

Test plan for "Limits of Rockwell to Brinell conversion". Specimens of SiC silicon carbide ceramic are measured under liquid helium -269 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Indentation size effect and load selection: industry application

Test plan for "Indentation size effect and load selection". Specimens of Cf/SiC ceramic matrix composite are measured under high-temperature oxidation in air at 900 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Hardness mapping across a weld heat-affected zone: industry application

Test plan for "Hardness mapping across a weld heat-affected zone". Specimens of PEEK engineering polymer are measured under steam atmosphere at 800 °C following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Effective case depth of carburised layers: industry application

Test plan for "Effective case depth of carburised layers". Specimens of fused silica are measured under combustion gas corrosion following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.

Read more →
Applications

Induction-hardened depth and transition zone: industry application

Test plan for "Induction-hardened depth and transition zone". Specimens of monocrystalline silicon wafer are measured under pure oxygen atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Nitrided layer hardness and brittleness rating: industry application

Test plan for "Nitrided layer hardness and brittleness rating". Specimens of electronic solder joint are measured under hydrogen reducing atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Laser-hardened track overlap evaluation: industry application

Test plan for "Laser-hardened track overlap evaluation". Specimens of DLC coating are measured under nitrogen protective atmosphere following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

Hardness anisotropy in additively manufactured parts: industry application

Test plan for "Hardness anisotropy in additively manufactured parts". Specimens of laser cladding layer are measured under multi-gas switching O2/H2/N2/H2O following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.

Read more →
Applications

Hot hardness and softening onset: industry application

Test plan for "Hot hardness and softening onset". Specimens of wire-arc additive part are measured under space environment: vacuum, cold, radiation following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.

Read more →
Applications

Low-temperature hardness and ductile-brittle transition: industry application

Test plan for "Low-temperature hardness and ductile-brittle transition". Specimens of graphite electrode are measured under multi-physics: thermal, mechanical, vacuum, EM following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.

Read more →
Applications

In-situ vacuum high-temperature indentation: industry application

Test plan for "In-situ vacuum high-temperature indentation". Specimens of wood and plywood are measured under SHPB strain rate 1e3-1e4 /s following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.

Read more →
Applications

Separating coating hardness from substrate effect: industry application

Test plan for "Separating coating hardness from substrate effect". Specimens of battery electrode sheet are measured under very-high-cycle fatigue at 20 kHz following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.

Read more →
Applications

Daily verification with reference blocks: industry application

Test plan for "Daily verification with reference blocks". Specimens of bearing raceway are measured under controlled 23±2 °C / 50±5 %RH following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.

Read more →
Applications

Indenter geometry and area-function calibration: industry application

Test plan for "Indenter geometry and area-function calibration". Specimens of turbine blade film hole are measured under ISO Class 7 cleanroom following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.

Read more →
Applications

Uncertainty budget for hardness measurement: industry application

Test plan for "Uncertainty budget for hardness measurement". Specimens of 20CrMnTi carburising steel are measured under in-line production environment following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.

Read more →
Applications

Empirical hardness to tensile strength correlation: industry application

Test plan for "Empirical hardness to tensile strength correlation". Specimens of H13 hot-work tool steel are measured under vibration and shock environment following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.

Read more →
Applications

Hardness sampling on small and thin parts: industry application

Test plan for "Hardness sampling on small and thin parts". Specimens of 316L stainless steel weld are measured under immersion in corrosive medium following hardness testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.

Read more →
Applications

Room-temperature tensile and yield strength: industry application

Test plan for "Room-temperature tensile and yield strength". Specimens of Ti-6Al-4V additively manufactured part are measured under combustion gas corrosion following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.

Read more →
Applications

Elevated-temperature tensile testing: industry application

Test plan for "Elevated-temperature tensile testing". Specimens of 2024 aluminium riveted joint are measured under pure oxygen atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.

Read more →
Applications

Cryogenic tensile and transition behaviour: industry application

Test plan for "Cryogenic tensile and transition behaviour". Specimens of Si3N4 silicon nitride ceramic are measured under hydrogen reducing atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.

Read more →
Applications

Compression behaviour and buckling check: industry application

Test plan for "Compression behaviour and buckling check". Specimens of C/C composite are measured under nitrogen protective atmosphere following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.

Read more →
Applications

Three- and four-point bending: industry application

Test plan for "Three- and four-point bending". Specimens of glass-fibre reinforced nylon are measured under multi-gas switching O2/H2/N2/H2O following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.

Read more →
Applications

Shear strength of riveted joints: industry application

Test plan for "Shear strength of riveted joints". Specimens of silicone rubber O-ring are measured under space environment: vacuum, cold, radiation following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.

Read more →
Applications

Torsion and shear modulus: industry application

Test plan for "Torsion and shear modulus". Specimens of sapphire window are measured under multi-physics: thermal, mechanical, vacuum, EM following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.

Read more →
Applications

Charpy impact and absorbed energy: industry application

Test plan for "Charpy impact and absorbed energy". Specimens of copper lead frame are measured under SHPB strain rate 1e3-1e4 /s following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

Low-temperature impact and fracture appearance: industry application

Test plan for "Low-temperature impact and fracture appearance". Specimens of TiN coating are measured under very-high-cycle fatigue at 20 kHz following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

SHPB dynamic compression at high strain rate: industry application

Test plan for "SHPB dynamic compression at high strain rate". Specimens of electroplated nickel layer are measured under controlled 23±2 °C / 50±5 %RH following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

High-cycle fatigue S-N curve: industry application

Test plan for "High-cycle fatigue S-N curve". Specimens of laser weld are measured under ISO Class 7 cleanroom following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.

Read more →
Applications

Ultrasonic very-high-cycle fatigue: industry application

Test plan for "Ultrasonic very-high-cycle fatigue". Specimens of powder metallurgy sintered part are measured under in-line production environment following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

Crack growth rate da/dN: industry application

Test plan for "Crack growth rate da/dN". Specimens of basalt fibre panel are measured under vibration and shock environment following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Fracture toughness K_IC and J-integral: industry application

Test plan for "Fracture toughness K_IC and J-integral". Specimens of rock thin section are measured under immersion in corrosive medium following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Creep and stress rupture: industry application

Test plan for "Creep and stress rupture". Specimens of photovoltaic ribbon are measured under post-irradiation hot cell following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Stress relaxation and preload loss: industry application

Test plan for "Stress relaxation and preload loss". Specimens of guideway surface are measured under ambient laboratory air following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Residual stress by hole drilling and indentation: industry application

Test plan for "Residual stress by hole drilling and indentation". Specimens of 42CrMo quenched and tempered steel are measured under high vacuum 1e-4 Pa following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Interlaminar shear of composites: industry application

Test plan for "Interlaminar shear of composites". Specimens of GCr15 bearing steel are measured under ultra-high vacuum 1e-7 Pa following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Bonded peel and lap-shear strength: industry application

Test plan for "Bonded peel and lap-shear strength". Specimens of 304 austenitic stainless steel are measured under vacuum thermal cycling -150 to +150 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Torque–preload relationship of fasteners: industry application

Test plan for "Torque–preload relationship of fasteners". Specimens of TC4 titanium alloy are measured under thermal shock at 300 K/s following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Multiaxial fatigue with phase-shifted loading: industry application

Test plan for "Multiaxial fatigue with phase-shifted loading". Specimens of Inconel 718 additively manufactured part are measured under high pressure 10 MPa at 1200 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Thermomechanical fatigue life: industry application

Test plan for "Thermomechanical fatigue life". Specimens of 7075 aluminium alloy are measured under liquid nitrogen -196 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Strain-rate sensitivity: industry application

Test plan for "Strain-rate sensitivity". Specimens of ZTA zirconia-toughened alumina are measured under liquid helium -269 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Grip compliance and frame correction: industry application

Test plan for "Grip compliance and frame correction". Specimens of Al2O3 alumina ceramic are measured under high-temperature oxidation in air at 900 °C following mechanical property testing. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Vision measurement of 2D profiles: industry application

Test plan for "Vision measurement of 2D profiles". Specimens of laser cladding layer are measured under high pressure 10 MPa at 1200 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

CMM measurement and position tolerance: industry application

Test plan for "CMM measurement and position tolerance". Specimens of wire-arc additive part are measured under liquid nitrogen -196 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Roundness and cylindricity evaluation: industry application

Test plan for "Roundness and cylindricity evaluation". Specimens of graphite electrode are measured under liquid helium -269 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Profile tolerance of free-form surfaces: industry application

Test plan for "Profile tolerance of free-form surfaces". Specimens of wood and plywood are measured under high-temperature oxidation in air at 900 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Roughness Ra/Rz and filtering: industry application

Test plan for "Roughness Ra/Rz and filtering". Specimens of battery electrode sheet are measured under steam atmosphere at 800 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Height and step measurement: industry application

Test plan for "Height and step measurement". Specimens of bearing raceway are measured under combustion gas corrosion following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Coating and sheet thickness: industry application

Test plan for "Coating and sheet thickness". Specimens of turbine blade film hole are measured under pure oxygen atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Ultrasonic testing and indication sizing: industry application

Test plan for "Ultrasonic testing and indication sizing". Specimens of 20CrMnTi carburising steel are measured under hydrogen reducing atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Magnetic particle and penetrant testing: industry application

Test plan for "Magnetic particle and penetrant testing". Specimens of H13 hot-work tool steel are measured under nitrogen protective atmosphere following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Eddy current testing and conductivity: industry application

Test plan for "Eddy current testing and conductivity". Specimens of 316L stainless steel weld are measured under multi-gas switching O2/H2/N2/H2O following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Vibration spectrum and fault diagnosis: industry application

Test plan for "Vibration spectrum and fault diagnosis". Specimens of TA15 titanium alloy are measured under space environment: vacuum, cold, radiation following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Borescope inspection of internal features: industry application

Test plan for "Borescope inspection of internal features". Specimens of Ti-6Al-4V additively manufactured part are measured under multi-physics: thermal, mechanical, vacuum, EM following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Thread and gear parameter measurement: industry application

Test plan for "Thread and gear parameter measurement". Specimens of 2024 aluminium riveted joint are measured under SHPB strain rate 1e3-1e4 /s following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Large-part measurement in situ: industry application

Test plan for "Large-part measurement in situ". Specimens of Si3N4 silicon nitride ceramic are measured under very-high-cycle fatigue at 20 kHz following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.

Read more →
Applications

Temperature compensation and CTE correction: industry application

Test plan for "Temperature compensation and CTE correction". Specimens of C/C composite are measured under controlled 23±2 °C / 50±5 %RH following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Point strategy and uncertainty: industry application

Test plan for "Point strategy and uncertainty". Specimens of glass-fibre reinforced nylon are measured under ISO Class 7 cleanroom following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Probe performance verification: industry application

Test plan for "Probe performance verification". Specimens of silicone rubber O-ring are measured under in-line production environment following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

In-line inspection and cycle time: industry application

Test plan for "In-line inspection and cycle time". Specimens of sapphire window are measured under vibration and shock environment following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.

Read more →
Applications

Automated loading integrated with measurement: industry application

Test plan for "Automated loading integrated with measurement". Specimens of copper lead frame are measured under immersion in corrosive medium following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.

Read more →
Applications

Vision guidance and robot positioning: industry application

Test plan for "Vision guidance and robot positioning". Specimens of TiN coating are measured under post-irradiation hot cell following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.

Read more →
Applications

Positioning accuracy of a precision stage: industry application

Test plan for "Positioning accuracy of a precision stage". Specimens of electroplated nickel layer are measured under ambient laboratory air following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.

Read more →
Applications

Writing an NDT procedure: industry application

Test plan for "Writing an NDT procedure". Specimens of laser weld are measured under high vacuum 1e-4 Pa following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.

Read more →
Applications

Acceptance levels for indications: industry application

Test plan for "Acceptance levels for indications". Specimens of powder metallurgy sintered part are measured under ultra-high vacuum 1e-7 Pa following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.

Read more →
Applications

Measurement system analysis: industry application

Test plan for "Measurement system analysis". Specimens of basalt fibre panel are measured under vacuum thermal cycling -150 to +150 °C following dimensional measurement and flaw detection. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.

Read more →
Applications

Grain size rating and statistics: industry application

Test plan for "Grain size rating and statistics". Specimens of copper lead frame are measured under ambient laboratory air following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Phase fraction by area analysis: industry application

Test plan for "Phase fraction by area analysis". Specimens of TiN coating are measured under high vacuum 1e-4 Pa following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Inclusion rating: industry application

Test plan for "Inclusion rating". Specimens of electroplated nickel layer are measured under ultra-high vacuum 1e-7 Pa following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Graphite morphology and nodularity: industry application

Test plan for "Graphite morphology and nodularity". Specimens of laser weld are measured under vacuum thermal cycling -150 to +150 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Coating thickness and interface morphology: industry application

Test plan for "Coating thickness and interface morphology". Specimens of powder metallurgy sintered part are measured under thermal shock at 300 K/s following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Weld penetration and heat-affected zone: industry application

Test plan for "Weld penetration and heat-affected zone". Specimens of basalt fibre panel are measured under high pressure 10 MPa at 1200 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Melt pool and porosity in additive parts: industry application

Test plan for "Melt pool and porosity in additive parts". Specimens of rock thin section are measured under liquid nitrogen -196 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.

Read more →
Applications

Cleanliness particle counting and classification: industry application

Test plan for "Cleanliness particle counting and classification". Specimens of photovoltaic ribbon are measured under liquid helium -269 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Bubble size distribution: industry application

Test plan for "Bubble size distribution". Specimens of guideway surface are measured under high-temperature oxidation in air at 900 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Fibre orientation and distribution: industry application

Test plan for "Fibre orientation and distribution". Specimens of 42CrMo quenched and tempered steel are measured under steam atmosphere at 800 °C following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

Crack length and propagation path: industry application

Test plan for "Crack length and propagation path". Specimens of GCr15 bearing steel are measured under combustion gas corrosion following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.

Read more →
Applications

Fractography and failure mode: industry application

Test plan for "Fractography and failure mode". Specimens of 304 austenitic stainless steel are measured under pure oxygen atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.

Read more →
Applications

Corrosion pit depth and density: industry application

Test plan for "Corrosion pit depth and density". Specimens of TC4 titanium alloy are measured under hydrogen reducing atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.

Read more →
Applications

Surface defect and scratch measurement: industry application

Test plan for "Surface defect and scratch measurement". Specimens of Inconel 718 additively manufactured part are measured under nitrogen protective atmosphere following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.

Read more →
Applications

Anisotropic structure under polarised light: industry application

Test plan for "Anisotropic structure under polarised light". Specimens of 7075 aluminium alloy are measured under multi-gas switching O2/H2/N2/H2O following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.

Read more →
Applications

Fluorescence labelling and biological samples: industry application

Test plan for "Fluorescence labelling and biological samples". Specimens of ZTA zirconia-toughened alumina are measured under space environment: vacuum, cold, radiation following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.

Read more →
Applications

Stereo observation and 3D topography: industry application

Test plan for "Stereo observation and 3D topography". Specimens of Al2O3 alumina ceramic are measured under multi-physics: thermal, mechanical, vacuum, EM following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.

Read more →
Applications

Automated stitching of large fields: industry application

Test plan for "Automated stitching of large fields". Specimens of carbon-fibre epoxy laminate are measured under SHPB strain rate 1e3-1e4 /s following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.

Read more →
Applications

Dimensional measurement and calibration: industry application

Test plan for "Dimensional measurement and calibration". Specimens of PTFE seal are measured under very-high-cycle fatigue at 20 kHz following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.

Read more →
Applications

AI-assisted phase recognition and segmentation: industry application

Test plan for "AI-assisted phase recognition and segmentation". Specimens of BK7 optical glass are measured under controlled 23±2 °C / 50±5 %RH following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.

Read more →
Applications

Correlating micrographs with hardness indents: industry application

Test plan for "Correlating micrographs with hardness indents". Specimens of SiC power device solder layer are measured under ISO Class 7 cleanroom following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.

Read more →
Applications

Choosing illumination and contrast mode: industry application

Test plan for "Choosing illumination and contrast mode". Specimens of WC-Co cemented carbide are measured under in-line production environment following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.

Read more →
Applications

Image drift and focus stability: industry application

Test plan for "Image drift and focus stability". Specimens of thermal barrier coating are measured under vibration and shock environment following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.

Read more →
Applications

Reproducibility of image measurements: industry application

Test plan for "Reproducibility of image measurements". Specimens of friction stir weld are measured under immersion in corrosive medium following microscopic observation and image measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.

Read more →
Applications

Guideway straightness with pitch and yaw: industry application

Test plan for "Guideway straightness with pitch and yaw". Specimens of PTFE seal are measured under ISO Class 7 cleanroom following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Angular error of a machine table: industry application

Test plan for "Angular error of a machine table". Specimens of BK7 optical glass are measured under in-line production environment following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Rotary table indexing error and backlash: industry application

Test plan for "Rotary table indexing error and backlash". Specimens of SiC power device solder layer are measured under vibration and shock environment following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

Parallelism of a straightedge and datum: industry application

Test plan for "Parallelism of a straightedge and datum". Specimens of WC-Co cemented carbide are measured under immersion in corrosive medium following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.

Read more →
Applications

Segmented stitching over long travel: industry application

Test plan for "Segmented stitching over long travel". Specimens of thermal barrier coating are measured under post-irradiation hot cell following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.

Read more →
Applications

Flatness of an optical table: industry application

Test plan for "Flatness of an optical table". Specimens of friction stir weld are measured under ambient laboratory air following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.

Read more →
Applications

Prism angle and refractive index: industry application

Test plan for "Prism angle and refractive index". Specimens of cold-sprayed coating are measured under high vacuum 1e-4 Pa following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fatigue limit and S-N curve with explicit limits of interpretation.

Read more →
Applications

Substrate figure and wedge angle: industry application

Test plan for "Substrate figure and wedge angle". Specimens of tungsten carbide spray powder are measured under ultra-high vacuum 1e-7 Pa following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports roundness and cylindricity with explicit limits of interpretation.

Read more →
Applications

Boresight parallelism of a telescope: industry application

Test plan for "Boresight parallelism of a telescope". Specimens of concrete core are measured under vacuum thermal cycling -150 to +150 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports inclusion rating and porosity with explicit limits of interpretation.

Read more →
Applications

Polygon and autocollimator combination: industry application

Test plan for "Polygon and autocollimator combination". Specimens of lithium battery copper foil are measured under thermal shock at 300 K/s following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports glass transition and melting point with explicit limits of interpretation.

Read more →
Applications

Abbe and cosine error correction: industry application

Test plan for "Abbe and cosine error correction". Specimens of gear tooth flank are measured under high pressure 10 MPa at 1200 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports crack length and growth rate with explicit limits of interpretation.

Read more →
Applications

Thermal drift in angular readings: industry application

Test plan for "Thermal drift in angular readings". Specimens of 45 carbon steel are measured under liquid nitrogen -196 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.

Read more →
Applications

Air turbulence and refractive index gradient: industry application

Test plan for "Air turbulence and refractive index gradient". Specimens of 40Cr alloy structural steel are measured under liquid helium -269 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.

Read more →
Applications

Collimation and focus judgement at long focal length: industry application

Test plan for "Collimation and focus judgement at long focal length". Specimens of DC53 cold-work die steel are measured under high-temperature oxidation in air at 900 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.

Read more →
Applications

Cross-check with laser interferometry: industry application

Test plan for "Cross-check with laser interferometry". Specimens of 2205 duplex stainless steel are measured under steam atmosphere at 800 °C following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.

Read more →
Applications

Sampling and filtering in photoelectric autocollimation: industry application

Test plan for "Sampling and filtering in photoelectric autocollimation". Specimens of GH4169 nickel-based superalloy are measured under combustion gas corrosion following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.

Read more →
Applications

Verifying sub-microradian resolution: industry application

Test plan for "Verifying sub-microradian resolution". Specimens of AlSi10Mg die-cast aluminium are measured under pure oxygen atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.

Read more →
Applications

Straightness calibration of a precision stage: industry application

Test plan for "Straightness calibration of a precision stage". Specimens of AZ91D magnesium alloy are measured under hydrogen reducing atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.

Read more →
Applications

Closed-loop feedback for precision motion: industry application

Test plan for "Closed-loop feedback for precision motion". Specimens of SiC silicon carbide ceramic are measured under nitrogen protective atmosphere following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.

Read more →
Applications

Thermal stability of granite and ceramic datums: industry application

Test plan for "Thermal stability of granite and ceramic datums". Specimens of Cf/SiC ceramic matrix composite are measured under multi-gas switching O2/H2/N2/H2O following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.

Read more →
Applications

Autocollimation in vacuum or at low temperature: industry application

Test plan for "Autocollimation in vacuum or at low temperature". Specimens of PEEK engineering polymer are measured under space environment: vacuum, cold, radiation following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.

Read more →
Applications

Coaxiality of an optical assembly: industry application

Test plan for "Coaxiality of an optical assembly". Specimens of fused silica are measured under multi-physics: thermal, mechanical, vacuum, EM following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

Uncertainty and traceability chain: industry application

Test plan for "Uncertainty and traceability chain". Specimens of monocrystalline silicon wafer are measured under SHPB strain rate 1e3-1e4 /s following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

Field versus laboratory agreement: industry application

Test plan for "Field versus laboratory agreement". Specimens of electronic solder joint are measured under very-high-cycle fatigue at 20 kHz following small-angle and straightness measurement. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

Cutting burn control on hardened steel: industry application

Test plan for "Cutting burn control on hardened steel". Specimens of 304 austenitic stainless steel are measured under high pressure 10 MPa at 1200 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

Distortion-free sectioning of sheet and foil: industry application

Test plan for "Distortion-free sectioning of sheet and foil". Specimens of TC4 titanium alloy are measured under liquid nitrogen -196 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

Retaining coating edges in cross-section: industry application

Test plan for "Retaining coating edges in cross-section". Specimens of Inconel 718 additively manufactured part are measured under liquid helium -269 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

Mounting and chamfering of thermal-spray coatings: industry application

Test plan for "Mounting and chamfering of thermal-spray coatings". Specimens of 7075 aluminium alloy are measured under high-temperature oxidation in air at 900 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.

Read more →
Applications

Vacuum impregnation of porous materials: industry application

Test plan for "Vacuum impregnation of porous materials". Specimens of ZTA zirconia-toughened alumina are measured under steam atmosphere at 800 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

Avoiding smearing between composite plies: industry application

Test plan for "Avoiding smearing between composite plies". Specimens of Al2O3 alumina ceramic are measured under combustion gas corrosion following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Preventing scratches and embedded abrasive in soft metals: industry application

Test plan for "Preventing scratches and embedded abrasive in soft metals". Specimens of carbon-fibre epoxy laminate are measured under pure oxygen atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Diamond polishing of ceramics and cemented carbide: industry application

Test plan for "Diamond polishing of ceramics and cemented carbide". Specimens of PTFE seal are measured under hydrogen reducing atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Electrolytic polishing of aluminium alloys: industry application

Test plan for "Electrolytic polishing of aluminium alloys". Specimens of BK7 optical glass are measured under nitrogen protective atmosphere following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Avoiding hydrogen pickup in titanium preparation: industry application

Test plan for "Avoiding hydrogen pickup in titanium preparation". Specimens of SiC power device solder layer are measured under multi-gas switching O2/H2/N2/H2O following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Sectioning across weld zones: industry application

Test plan for "Sectioning across weld zones". Specimens of WC-Co cemented carbide are measured under space environment: vacuum, cold, radiation following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Measuring heat-affected zone width: industry application

Test plan for "Measuring heat-affected zone width". Specimens of thermal barrier coating are measured under multi-physics: thermal, mechanical, vacuum, EM following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Preparation for grain size measurement: industry application

Test plan for "Preparation for grain size measurement". Specimens of friction stir weld are measured under SHPB strain rate 1e3-1e4 /s following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Consistency for inclusion rating: industry application

Test plan for "Consistency for inclusion rating". Specimens of cold-sprayed coating are measured under very-high-cycle fatigue at 20 kHz following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →
Applications

Preserving graphite morphology in cast iron: industry application

Test plan for "Preserving graphite morphology in cast iron". Specimens of tungsten carbide spray powder are measured under controlled 23±2 °C / 50±5 %RH following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports speckle quality and subset error with explicit limits of interpretation.

Read more →
Applications

Porosity preparation for additive parts: industry application

Test plan for "Porosity preparation for additive parts". Specimens of concrete core are measured under ISO Class 7 cleanroom following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports effective case depth with explicit limits of interpretation.

Read more →
Applications

Cross-sectioning of battery electrodes: industry application

Test plan for "Cross-sectioning of battery electrodes". Specimens of lithium battery copper foil are measured under in-line production environment following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports impact absorbed energy KV2 with explicit limits of interpretation.

Read more →
Applications

Ion-beam polishing of semiconductor cross-sections: industry application

Test plan for "Ion-beam polishing of semiconductor cross-sections". Specimens of gear tooth flank are measured under vibration and shock environment following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports flatness and parallelism with explicit limits of interpretation.

Read more →
Applications

Petrographic thin section preparation: industry application

Test plan for "Petrographic thin section preparation". Specimens of 45 carbon steel are measured under immersion in corrosive medium following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports grain size and phase fraction with explicit limits of interpretation.

Read more →
Applications

Protecting fracture surfaces during sectioning: industry application

Test plan for "Protecting fracture surfaces during sectioning". Specimens of 40Cr alloy structural steel are measured under post-irradiation hot cell following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coefficient of thermal expansion with explicit limits of interpretation.

Read more →
Applications

Reproducible automatic polishing parameters: industry application

Test plan for "Reproducible automatic polishing parameters". Specimens of DC53 cold-work die steel are measured under ambient laboratory air following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports strain and displacement field with explicit limits of interpretation.

Read more →
Applications

Effect of preparation quality on hardness: industry application

Test plan for "Effect of preparation quality on hardness". Specimens of 2205 duplex stainless steel are measured under high vacuum 1e-4 Pa following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports cleanliness particle count with explicit limits of interpretation.

Read more →
Applications

Consumable selection and cost control: industry application

Test plan for "Consumable selection and cost control". Specimens of GH4169 nickel-based superalloy are measured under ultra-high vacuum 1e-7 Pa following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports ion or electron beam spot size with explicit limits of interpretation.

Read more →
Applications

Preparation safety and waste handling: industry application

Test plan for "Preparation safety and waste handling". Specimens of AlSi10Mg die-cast aluminium are measured under vacuum thermal cycling -150 to +150 °C following sectioning, mounting and polishing workflow. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elastic and reduced modulus with explicit limits of interpretation.

Read more →
Applications

3D-printed specimens and conformal fixtures: industry application

Test plan for "3D-printed specimens and conformal fixtures". Specimens of photovoltaic ribbon are measured under space environment: vacuum, cold, radiation following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports acquisition rate and synchronisation error with explicit limits of interpretation.

Read more →
Applications

Teaching practice and operator assessment: industry application

Test plan for "Teaching practice and operator assessment". Specimens of guideway surface are measured under multi-physics: thermal, mechanical, vacuum, EM following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports die warpage and solder void rate with explicit limits of interpretation.

Read more →
Applications

Hardness consumables and indenter management: industry application

Test plan for "Hardness consumables and indenter management". Specimens of 42CrMo quenched and tempered steel are measured under SHPB strain rate 1e3-1e4 /s following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports yield and tensile strength with explicit limits of interpretation.

Read more →
Applications

Consumable consistency across batches: industry application

Test plan for "Consumable consistency across batches". Specimens of GCr15 bearing steel are measured under very-high-cycle fatigue at 20 kHz following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports creep rate and stress rupture strength with explicit limits of interpretation.

Read more →
Applications

Automated sample pre-treatment: industry application

Test plan for "Automated sample pre-treatment". Specimens of 304 austenitic stainless steel are measured under controlled 23±2 °C / 50±5 %RH following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports surface roughness Ra/Rz with explicit limits of interpretation.

Read more →
Applications

Automated handling with barcode traceability: industry application

Test plan for "Automated handling with barcode traceability". Specimens of TC4 titanium alloy are measured under ISO Class 7 cleanroom following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports coating thickness and adhesion with explicit limits of interpretation.

Read more →
Applications

Robot and vision positioning: industry application

Test plan for "Robot and vision positioning". Specimens of Inconel 718 additively manufactured part are measured under in-line production environment following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports leak rate and outgassing rate with explicit limits of interpretation.

Read more →
Applications

Instrument interface and LIMS: industry application

Test plan for "Instrument interface and LIMS". Specimens of 7075 aluminium alloy are measured under vibration and shock environment following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports wear volume and friction coefficient with explicit limits of interpretation.

Read more →
Applications

Raising acquisition from 40 Hz to 100 Hz: industry application

Test plan for "Raising acquisition from 40 Hz to 100 Hz". Specimens of ZTA zirconia-toughened alumina are measured under immersion in corrosive medium following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports positioning accuracy and repeatability with explicit limits of interpretation.

Read more →
Applications

Synchronised force and displacement at high temperature: industry application

Test plan for "Synchronised force and displacement at high temperature". Specimens of Al2O3 alumina ceramic are measured under post-irradiation hot cell following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports predicted vs measured property deviation with explicit limits of interpretation.

Read more →
Applications

Servo bandwidth and motion smoothness: industry application

Test plan for "Servo bandwidth and motion smoothness". Specimens of carbon-fibre epoxy laminate are measured under ambient laboratory air following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports elongation and reduction of area with explicit limits of interpretation.

Read more →
Applications

Full automation and unattended operation: industry application

Test plan for "Full automation and unattended operation". Specimens of PTFE seal are measured under high vacuum 1e-4 Pa following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports residual stress field with explicit limits of interpretation.

Read more →
Applications

Retrofit of legacy instruments: industry application

Test plan for "Retrofit of legacy instruments". Specimens of BK7 optical glass are measured under ultra-high vacuum 1e-7 Pa following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports dimensional deviation and position with explicit limits of interpretation.

Read more →
Applications

AI material database and selection advice: industry application

Test plan for "AI material database and selection advice". Specimens of SiC power device solder layer are measured under vacuum thermal cycling -150 to +150 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports element content and grade identification with explicit limits of interpretation.

Read more →
Applications

AI property prediction from experiments: industry application

Test plan for "AI property prediction from experiments". Specimens of WC-Co cemented carbide are measured under thermal shock at 300 K/s following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports vacuum level and pump-down curve with explicit limits of interpretation.

Read more →
Applications

Automated test-sequence orchestration: industry application

Test plan for "Automated test-sequence orchestration". Specimens of thermal barrier coating are measured under high pressure 10 MPa at 1200 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports conductivity and resistivity with explicit limits of interpretation.

Read more →
Applications

Condition monitoring and predictive maintenance: industry application

Test plan for "Condition monitoring and predictive maintenance". Specimens of friction stir weld are measured under liquid nitrogen -196 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports servo bandwidth and following error with explicit limits of interpretation.

Read more →
Applications

Calibration interval and intermediate checks: industry application

Test plan for "Calibration interval and intermediate checks". Specimens of cold-sprayed coating are measured under liquid helium -269 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports hardness value and distribution with explicit limits of interpretation.

Read more →
Applications

Laboratory safety and emergency stop: industry application

Test plan for "Laboratory safety and emergency stop". Specimens of tungsten carbide spray powder are measured under high-temperature oxidation in air at 900 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports fracture toughness K_IC with explicit limits of interpretation.

Read more →
Applications

Central monitoring of multiple instruments: industry application

Test plan for "Central monitoring of multiple instruments". Specimens of concrete core are measured under steam atmosphere at 800 °C following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports angular deviation and straightness with explicit limits of interpretation.

Read more →
Applications

Data integrity and audit trail: industry application

Test plan for "Data integrity and audit trail". Specimens of lithium battery copper foil are measured under combustion gas corrosion following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports refractive index and thickness with explicit limits of interpretation.

Read more →
Applications

Method files and work instructions: industry application

Test plan for "Method files and work instructions". Specimens of gear tooth flank are measured under pure oxygen atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports thermal conductivity and diffusivity with explicit limits of interpretation.

Read more →
Applications

Training and competence matrix: industry application

Test plan for "Training and competence matrix". Specimens of 45 carbon steel are measured under hydrogen reducing atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports temperature uniformity and control deviation with explicit limits of interpretation.

Read more →
Applications

Acceptance and rollback of a retrofit: industry application

Test plan for "Acceptance and rollback of a retrofit". Specimens of 40Cr alloy structural steel are measured under nitrogen protective atmosphere following support process and automation integration. The plan fixes sampling, measurement parameters, acceptance basis and record format, and reports magnetic particle or UT indication size with explicit limits of interpretation.

Read more →

Research applications by series

Science & principles

Prism couplers

Translation pending review.

高折射率棱镜与样品之间形成可控耦合间隙。扫描角度时,满足相位匹配的导模引起反射强度特征,用模式位置与薄膜模型分析有效折射率及膜厚。

Explore principles, workflow and evidence →

Your next research question. Let’s explore.

Tell us about your material, specimen and measurement goal.

Discuss your application ↗
Find your instrument
⌕
Search products, cases, solutions, standards and literature.